Quick answer: a 40 × 30 ft house (1,200 sq ft) costs about $11,550 on a concrete slab, the middle of HomeGuide’s $5.75–13.50 per sq ft. A crawl space comes to about $12,600 and a full basement about $34,200 at Angi’s $20–37 per sq ft. These are published estimates; local quotes vary.

How the concrete foundation cost calculator works
The calculator prices a whole foundation from the size of the house. You enter the length and width of the footprint and pick a foundation type. It multiplies the area by a published installed price for your country. The result is the middle of that published range, with the low and high ends shown underneath.
Installed prices already include the concrete, the labor, the forms and the contractor’s margin. That is how foundation guides and most contractors quote, so it is the fairest way to check a quote. It is not a takeoff. The tool does not add up yards of concrete, bars of steel or hours of labor line by line. Further down, this page shows those quantities for one example house, so you can see what sits inside the per-square-foot rate.
- Footprint: house length × width, in feet or meters. Use the outside size of the foundation.
- Pick the type: slab on grade, crawl space, full basement or pier and beam. Germany also has an insulated slab. In the UK and Germany you can price strip footings, and in the UK trench fill too.
- Area prices: area × the published low, middle and high price per sq ft or per m².
- Length prices: strip and trench-fill footings are priced per metre, so the tool uses the perimeter, 2 × (L + W), instead of the area.
- Your price: type a rate from a quote and it replaces the middle figure. The published range stays on screen for comparison.
Cost = L × W × price per area (strip or trench fill: 2 × (L + W) × price per metre)
The middle is the plain average of the low and high ends, unless the source gives its own typical figure. Checkatrade gives a typical £230 per m² for a raft, for example, and the tool uses that. Where a source gives one figure only, as HomeStars does for Canada, the low, middle and high are all the same number.
If a type has no reliable published price in your country, the tool says so and asks for your own. It never fills the gap with a price from another country, and it never converts currencies. For the concrete alone, by the yard or m³, use the concrete cost calculator, which adds delivery and short-load fees.
Concrete foundation cost per square foot in 2026
Three US guides publish per-square-foot foundation prices, and they mostly agree on slabs and crawl spaces. They part ways on basements. None of them says which cities or year its prices come from, and HomeGuide shows no date at all. Read every figure as a rough national guide.
| Foundation type | HomeGuide (undated) | Angi (Jul 2024) | Fixr (Feb 2026) |
|---|---|---|---|
| Concrete slab | $5.75–13.50 | $5–16 (monolithic) | $4–14 |
| Slab on grade | not split out | not split out | $4–12 |
| Monolithic slab | $5–14 | $5–16 | $4–16 |
| Stem wall slab | $50 per linear ft | not published | $6–18 |
| Reinforced 6 in slab | $6.40–10.30 | not published | not published |
| Crawl space | $7–14 | $6–18 | $10–18 |
| Pier and beam | $7–11 | $6–12 | $6–15 |
| Full basement | $33 average (unfinished) | $20–37 | $20–50 |
HomeAdvisor publishes the same basement ($20–37) and pier and beam ($6–12) figures as Angi. Both belong to Angi Inc., so they count as one source, not two.
Fixr’s own numbers don’t quite fit together. Its slab subtypes, monolithic at $4–16 and stem wall at $6–18, run past its headline slab maximum of $14. HomeGuide has the same kind of problem: it gives a slab as both $5–14 and $5.75–13.50 on the same page. Neither is wrong as such. They show how loose these ranges are.
Why the US basement figures spread so far
At $20 per sq ft, a 1,200 sq ft basement is $24,000. At Fixr’s $50 it is $60,000. That gap comes from what a basement is. Most of the cost is digging and walls, not the floor. HomeGuide splits a basement budget into excavation 45%, walls 38% and floor 17%.
So soil, depth and water decide the price. A dig in light soil costs a fraction of one in wet clay or rock, and a high water table brings drainage and waterproofing. Fixr’s top end probably covers those harder sites, though it doesn’t say so. The calculator uses Angi’s $20–37 because it is dated and brackets HomeGuide’s $33 average. If your site has rock or water, expect the top of Fixr’s range.
Slab, crawl space or basement: cost side by side
The same house costs very different amounts depending on what holds it up. Here is the default 40 × 30 ft house priced each way with the calculator’s US prices. Every figure is 1,200 sq ft × the published rate.
Slab on grade. The slab is the ground floor. It is the cheapest and quickest option on flat, stable ground in mild climates. In cold areas the edge or footing still has to reach below the local frost line, which makes it deeper and dearer. Plumbing runs in or under the slab, so repairs later mean cutting concrete.
Monolithic slab. The slab and its thickened edge are poured in one go. It saves a pour and a set of forms over a slab on separate footings, which is why it sits at the low end of the slab ranges. It suits warm climates with shallow frost depths.
Stem wall slab. A footing is poured first, then a short wall, then the slab inside it. It costs more, Fixr’s $6–18 against $4–12 for slab on grade, but it lifts the floor above grade on sloping or flood-prone lots.
Crawl space. Short walls on footings hold a wood floor above the ground. You get access to plumbing and ducts from below. The space needs a vapour barrier and ventilation or sealing, which add to the bill and to upkeep.
Full basement. Walls about 8 ft high on footings, with a slab at the bottom of a deep dig. It costs the most, but you get usable space. In cold climates the footings must go deep anyway, so the extra dig to a full basement costs less than it would where frost is shallow.
Pier and beam. Concrete piers carry beams under a wood floor. HomeGuide puts it at $7–11 per sq ft, close to a slab. Builders use it on sloping sites and on soils that swell and shrink, where a slab would be at risk of cracking.
What goes into the price: concrete, labor, excavation and steel
An installed price per square foot hides several jobs. Knowing them helps you read a quote and spot what is missing. HomeGuide splits a plain slab into $2.60 per sq ft of labor and $3.81 of concrete, $6.41 in all. Its size table adds up, which is worth checking because not every table on that page does.
| House size | Labor | Materials | HomeGuide total | Check: labor + materials |
|---|---|---|---|---|
| 800 sq ft | $2,100 | $3,000 | $5,100 | $5,100 |
| 1,200 sq ft | $3,100 | $4,600 | $7,700 | $7,700 (1,200 × $6.41 = $7,692) |
| 2,400 sq ft | $6,200 | $9,100 | $15,300 | $15,300 |
Labor works out at 2.60 ÷ 6.41 = 41% of that slab. Fixr gives 40–60% for foundations in general. Walls and deep footings take more forming time than a flat slab, so labor’s share rises with a crawl space or basement.
Concrete. HomeGuide gives ready-mix at $120–150 per cu yd and footings at $150 per cu yd. On a basement that needs 45 cu yd, the concrete alone is $5,440–6,800. On a slab it is closer to $2,200–2,700. The quantities are in the next section.
Excavation. HomeGuide prices digging at $2.50–6 per cu yd in light soil, $6–10 in average soil, $10–15 in heavy or wet soil and $50–200 where rock has to be broken. A new basement dig runs $10–20 per sq ft. Fine grading for a slab is $0.40–2 per sq ft.
Steel. HomeGuide lists reinforcement at $150–500 as a line item and rebar for a raft at $1–2 per sq ft. A Minnesota building department recommends two continuous #4 bars in footings, 3 in above the bottom. Code and your engineer set the real amount.
| Item | Published price | Source and date |
|---|---|---|
| Building permit | $500–1,500 (some cities $30–150 flat); up to $2,300 | HomeGuide, undated; Fixr, Feb 2026 |
| Geotechnical soil test | $1,000–5,000 | HomeGuide, undated |
| Structural engineer | $100–220 an hour | HomeGuide, undated |
| Foundation inspections | $150–1,300 in total | HomeGuide, undated |
| Basement waterproofing | $1,900–6,300; about $5,000 average | HomeGuide, undated; Fixr, Feb 2026 |
| Footings (where priced apart) | $6.50 per sq ft or $150 per cu yd | HomeGuide, undated; Angi, Jul 2024 |
| Reinforcement | $150–500; raft rebar $1–2 per sq ft | HomeGuide, undated |
| Fine grading | $0.40–2 per sq ft | HomeGuide, undated |
| Vapour barrier, under-slab insulation | no reliable US figure found | none of the guides above gives one |
Ask each contractor which of these lines their price covers. Two quotes that look $5,000 apart may cover the same work once you add the permit, the soil test and the waterproofing to the cheaper one.
Footing and wall concrete for each foundation type
The calculator prices by area, but the concrete in each type is very different. This table works it out for a 30 × 40 ft house. The sizes are examples to show the arithmetic, not a design. The footing size comes from your local code table and your engineer.
For scale, the IRC minimum footing, as adopted in Washington State, is 12 in wide and 6 in deep. ACI 332 sets a minimum poured foundation wall of 7.5 in actual thickness. The examples below use a wider 16 × 8 in footing under an 8 in wall.
| Item | Monolithic slab | Crawl space (4 ft walls) | Full basement (8 ft walls) |
|---|---|---|---|
| Edge or footing | 12 × 12 in edge: 3.36 yd³ | 16 × 8 in footing: 4.52 yd³ | 16 × 8 in footing: 4.52 yd³ |
| Walls, 8 in thick | none | 13.56 yd³ | 27.13 yd³ |
| Floor slab, 4 in | 1,200 sq ft: 14.81 yd³ | none (vapour barrier on soil) | 1,108 sq ft inside walls: 13.68 yd³ |
| Total concrete | 18.17 yd³ | 18.09 yd³ | 45.33 yd³ |
| Concrete at $120–150 per yd³ | $2,181–2,726 | $2,170–2,713 | $5,440–6,800 |
| Gravel base, 4 in | 14.81 yd³ | none | 13.68 yd³ |
| Excavation | grading only | trench for footings | pit 44 × 34 × 8 ft = 443 yd³ |
How the numbers work
Measure on the centreline. Walls and footings meet at the corners. If you run the outside perimeter, 2 × (40 + 30) = 140 ft, the four corners get counted twice. Use the centreline instead: the outside perimeter minus 4 × the wall thickness. For an 8 in wall that is 140 − 4 × 0.667 = 137.33 ft. A 12 in edge gives 140 − 4 × 1 = 136 ft.
One competing calculator uses 140 ft for footings but 136 ft for the edge of the same house. Pick one method and stick to it. The centreline is exact for a rectangle.
- Footing: 1.333 ft × 0.667 ft × 137.33 ft = 122.07 cu ft ÷ 27 = 4.52 yd³.
- Crawl space wall: 0.667 × 4 × 137.33 = 366.22 cu ft = 13.56 yd³.
- Basement wall: 0.667 × 8 × 137.33 = 732.44 cu ft = 27.13 yd³, or 0.1975 yd³ per foot of wall.
- Basement slab: inside the walls, (40 − 1.333) × (30 − 1.333) = 1,108.4 sq ft × 0.333 ft = 369.5 cu ft = 13.68 yd³.
- Monolithic slab: 1,200 × 0.333 = 400 cu ft = 14.81 yd³, plus the edge below the slab, 136 × 1 × 0.667 = 90.67 cu ft = 3.36 yd³.
Add 5–10% for waste when you order, because uneven trench bottoms eat concrete. For your own sizes, the concrete footing calculator works out footing yards, and the concrete wall calculator does the walls. For the slab and gravel base, use the concrete calculator and the gravel calculator.
Excavation for the basement: two rates that don’t match
The basement pit in the table allows 2 ft of working room on each side, an example figure, so it is 44 × 34 ft and 8 ft deep. That is 11,968 cu ft, or 443 cu yd. At HomeGuide’s $6–10 per cu yd for average soil, the dig is $2,660–4,433.
HomeGuide’s other figure for a new basement dig is $10–20 per sq ft, which is $12,000–24,000 for 1,200 sq ft. The page doesn’t explain the gap. The per-yard rate looks like machine time only. The per-sq-ft rate probably includes hauling the spoil, backfill and grading. For a budget, use the higher figure until you have a quote.
Foundation cost by house size (1,000 to 3,000 sq ft)
These totals are the calculator’s US prices × the area, so every figure is one multiplication you can check. The middle is what the calculator shows as the main result. Fixr’s column is its own published range across all foundation types.
| Footprint | Slab $5.75–13.50 | Crawl space $7–14 | Basement $20–37 | Fixr, all types (Feb 2026) |
|---|---|---|---|---|
| 1,000 sq ft | $5,750–13,500 ($9,625) | $7,000–14,000 ($10,500) | $20,000–37,000 ($28,500) | $5,000–35,000 |
| 1,500 sq ft | $8,625–20,250 ($14,437.50) | $10,500–21,000 ($15,750) | $30,000–55,500 ($42,750) | $7,500–52,500 |
| 2,000 sq ft | $11,500–27,000 ($19,250) | $14,000–28,000 ($21,000) | $40,000–74,000 ($57,000) | $10,000–70,000 |
| 2,500 sq ft | $14,375–33,750 ($24,062.50) | $17,500–35,000 ($26,250) | $50,000–92,500 ($71,250) | $12,500–87,500 |
| 3,000 sq ft | $17,250–40,500 ($28,875) | $21,000–42,000 ($31,500) | $60,000–111,000 ($85,500) | $15,000–105,000 |
Check a row: 2,000 × $5.75 = $11,500 and 2,000 × $13.50 = $27,000. The middle is 2,000 × $9.625 = $19,250. HomeGuide’s own table differs slightly on some rows. For 2,400 sq ft it lists a slab from $13,900, though 2,400 × $5.75 is $13,800.
Real quotes don’t scale in a straight line. The permit, soil test, engineer and getting the crew and machines to site cost about the same on a small house as a big one. So the price per square foot falls as the house gets bigger, and a very small foundation often costs more per square foot than any range here. The calculator is linear, so add those fixed costs to small jobs yourself.
Two storeys on a smaller footprint need less foundation than one storey with the same floor area. Price the footprint, not the living space.
Foundation costs by country
The calculator switches its prices when you change country. Each price stays in the currency and unit its source uses, with the publisher and the date on the page. Foundation types differ by market too. Crawl spaces and pier and beam are North American; the UK builds on strip, trench-fill and raft foundations.
| Market | Foundation type | Published price | Source and date |
|---|---|---|---|
| United States | Slab | $5.75–13.50 per sq ft | HomeGuide, undated |
| United States | Crawl space | $7–14 per sq ft | HomeGuide, undated |
| United States | Full basement | $20–37 per sq ft (HomeGuide $33 average; Fixr $20–50) | Angi, updated Jul 12, 2024 |
| United States | Pier and beam | $7–11 per sq ft | HomeGuide, undated |
| United States | Insulated slab | no reliable figure found | none |
| Canada | Slab | $8 per sq ft (CAD) | HomeStars Toronto, updated 21/08/2026 |
| Canada | Crawl space | $15 per sq ft (CAD) | HomeStars Toronto, updated 21/08/2026 |
| Canada | Basement | $35 per sq ft (CAD) | HomeStars Toronto, updated 21/08/2026 |
| Canada | Foundation, general (Calgary) | $6–15 per sq ft; slab pouring $5.50–9 | HomeStars Calgary, undated |
| Canada | Basement floor slab only | $4–8 per sq ft | HomeStars slab guide, undated |
| Canada | Pier and beam | no reliable figure found | none |
| United Kingdom | Raft (the tool’s “Slab on grade”) | £200–260 per m², £230 typical (MyJobQuote £150–300) | Checkatrade, cost table May 2024; MyJobQuote, 18/09/26 |
| United Kingdom | Strip footing | £95–115 per metre by excavator; £170–220 hand dug | Checkatrade, cost table May 2024 |
| United Kingdom | Trench fill | £130–160 per metre, £145 typical | Checkatrade, cost table May 2024 |
| United Kingdom | Basement, crawl space, pier and beam | no per-m² figure found | none |
| Australia | House slab | $75–110 per m² (AUD); standard residential $70–100 | Yellow Pages, updated May 2026 |
| Australia | Other types (waffle pod, raft, basement) | no reliable figure found | none |
| New Zealand | Any house foundation | no reliable figure found; generic slab only, $50–70 per m² | Airtasker NZ, updated 31 Oct 2026 |
| Germany | Bodenplatte (simple slab) | €120–160 per m² | sanier.de, 27 Jul 2026 |
| Germany | Insulated Bodenplatte | €160–220 per m² | sanier.de, 27 Jul 2026 |
| Germany | Keller (cast-in-place basement) | €250–400 per m²; precast €150–200 | Hausjournal, updated 31.10.2024 |
| Germany | Streifenfundament (strip) | €150–250 per running metre | sanier.de, updated 17 Dec 2025 |
| Germany | Trench fill, crawl space, pier and beam | no reliable figure found | none |
Canada
As a concrete foundation cost calculator for Canada, the tool uses HomeStars Toronto: slab $8, crawlspace $15 and basement $35 per sq ft. Each is a single figure, so the low, middle and high come out the same. HomeStars Calgary gives a wider $6–15 per sq ft for foundation construction, which shows how much a single figure leaves out. Every Canadian price here comes from one publisher, and none covers pier and beam.
For a basement floor poured inside existing walls, HomeStars gives $4–8 per sq ft, or $2,400–4,800 for 600 sq ft. That is the slab only, not the walls or the dig, so don’t compare it with the $35 basement figure.
United Kingdom
As a concrete foundation cost calculator for the UK, the tool uses Checkatrade’s cost table, dated May 2024. A strip foundation, dug by excavator 1 m deep and 0.6 m wide with 0.3 m of concrete, is £95–115 per metre. Trench fill, with 0.7 m of concrete, is £130–160 per metre. A raft is £200–260 per m². The tool lists the raft under “Slab on grade”, and its source line names it as a raft.
MyJobQuote (updated 18/09/26) prices strip and trench fill per m² of building instead. For a 15 × 9 m footprint it gives £70–78 per m² for strip and £84–87 for trench fill. That is 135 m² × £70–78 = £9,450–10,530 for a strip foundation. Checkatrade’s rate on the same house gives 48 m × £95–115 = £4,560–5,520.
The two can’t both be the whole job. MyJobQuote’s figure likely includes things Checkatrade’s per-metre rate does not, such as internal walls, spoil removal or a ground floor. Neither page says exactly. Use the per-metre price for the outside trench only, and add internal load-bearing walls and spoil to it.
For depth and width, NHBC says strip foundations should be 150–500 mm thick and trench fill at least 500 mm, at least 50 mm wider than the wall on each side. Building control decides the depth on clay or near trees.
Australia
Yellow Pages (updated May 2026) gives $75–110 per m² for a house foundation slab, which is the calculator default. On the default 12 × 9 m house that is 108 × $75–110 = $8,100–11,880, with $9,990 in the middle. The same publisher gives $70–100 for a standard residential slab, and Airtasker $65–85 for a plain slab. CalcWall found no guide that separates waffle pod from stiffened raft slabs, and no published rate for footings by the metre.
New Zealand
CalcWall found no reliable published price for a house foundation in New Zealand. No guide gives a per-m² figure for RibRaft, X-Pod or a standard slab and footing system. The only figure is Airtasker NZ’s $50–70 per m² for a concrete slab, updated 31 October 2026. That is a generic slab, the kind used for a patio or shed, not a house foundation.
So the calculator shows no default for New Zealand. Get a price per m² from a local builder or foundation contractor and type it into the price box. Don’t use the Airtasker figure for a house, because a house slab has footings, steel, insulation and engineering that a garden slab does not.
Germany
German guides split into two groups that look far apart. sanier.de’s foundations guide (updated 17 Dec 2025) lists a large Plattenfundament for a house at €70–100 per m². Its own Bodenplatte article (27 Jul 2026) gives €120–160 per m² for a simple slab, and Hausjournal gives €130–250 per m² all in, earthworks included.
The €70–100 figure is a short table entry with no list of what it covers. It probably leaves out insulation and earthworks, which the higher figures include. The calculator uses €120–160 because it is the newer, more detailed figure. If your quote covers the concrete slab and steel only, €70–100 may fit it. If it covers digging, gravel, insulation and drainage, expect €130–250.
For a basement, Hausjournal gives €250–400 per m² cast in place, €150–200 precast and €200–400 for a basement shell in general. For strip footings, sanier.de gives €150–250 per running metre. Hausjournal’s €200–350 is per m² of strip area, a different unit, so don’t put it in the per-metre box. No German guide found gives a trench-fill rate, so that option doesn’t appear for Germany.
Ways to lower the cost without cutting corners
The foundation is the one part of a house you can’t fix cheaply later. Savings should come from design and planning, not from thinner concrete or less steel than the engineer asks for.
- Keep the shape simple. A rectangle has a short perimeter for its area. Every corner and jog adds forms, footing length and labor.
- Test the soil early. A $1,000–5,000 soil test (HomeGuide) costs less than a redesign after the dig finds clay or rock.
- Match the type to the site. On a flat, dry lot in a mild climate, a slab is usually cheapest. On a slope, a stem wall or crawl space may cost less than the fill a slab would need.
- Get like-for-like quotes. Ask every contractor to list excavation, steel, waterproofing, permits and backfill. Then compare the totals.
- Plan the pour. A pump, waiting time and a part load on the last truck all add cost. Have forms, steel and inspections done before the trucks arrive.
- Think about the basement honestly. Where footings must go deep for frost anyway (60 in in one Minnesota city), a basement adds space for less than it costs elsewhere. Where frost is shallow, a slab or crawl space is far cheaper.
Don’t skip the inspection of the footing trench and steel before the pour. It costs little, and a bad footing found after framing costs far more than any saving.
Worked examples
Each example matches the calculator with the default prices. Enter the same sizes to check.
US slab, 40 × 30 ft. Area: 40 × 30 = 1,200 sq ft. Low: 1,200 × $5.75 = $6,900. High: 1,200 × $13.50 = $16,200. Middle: ($5.75 + $13.50) ÷ 2 = $9.625 per sq ft, × 1,200 = $11,550.00. The tool shows $9.63 per sq ft (HomeGuide, undated).
US full basement, same house. 1,200 × $20 = $24,000 up to 1,200 × $37 = $44,400. Middle: $28.50 × 1,200 = $34,200.00 (Angi, Jul 2024). That is $22,650 more than the slab, about three times the price.
UK, 12 × 9 m house. Raft: 108 m² × £200–260 = £21,600–28,080, typical £230 → £24,840.00. Strip footing: perimeter 2 × (12 + 9) = 42 m × £95–115 = £3,990–4,830, typical £105 → £4,410.00. Trench fill: 42 × £130–160 = £5,460–6,720, typical £145 → £6,090.00 (Checkatrade, May 2024).
Germany, 12 × 9 m. Simple Bodenplatte: 108 m² × €120–160 = 12.960–17.280 €, middle €140 → 15.120,00 €. Insulated: 108 × €160–220 = 17.280–23.760 €, middle €190 → 20.520,00 € (sanier.de, Jul 2026).
Your own quote, UK. A groundworker quotes a raft at £215 per m² for the 12 × 9 m house. Type 215 in the price box: 108 × £215 = £23,220.00. The published £21,600–28,080 stays on screen, and the quote sits near the low end.
Canada, in feet. Switch the units to feet and enter 40 × 30. Slab: 1,200 × $8 = $9,600.00. Basement: 1,200 × $35 = $42,000.00 (HomeStars Toronto, Aug 2026). With the metric defaults, 12 × 9 m is 108 m², which the tool turns into 1,162.5 sq ft, so the slab shows $9,300.02.
In New Zealand the tool shows no figure until you type a price per m² from a local quote. It then multiplies your rate by the area, the same way.
Notes for builders
Centreline, always. Run footings and walls on the centreline, outside perimeter minus 4 × the thickness. The outside perimeter counts every corner twice.
Frost first. Exterior footings go below the local frost depth and at least 12 in into undisturbed ground. One Minnesota city sets 60 in. Ask your building department.
Read the unit. UK and German strip prices are per metre of trench, rafts per m² of floor. A per-m²-of-footprint strip price is a different thing.
Price the dig apart. On a basement, excavation is about 45% of the cost (HomeGuide). Get the dig priced by someone who has seen the soil.
Wall thickness, footing size and steel on this page are a guide. Local code and the engineer of record decide what a house foundation needs. If the walls are block rather than poured, the concrete block calculator counts the blocks and core fill.
Sources
Where the numbers on this page come from. Everything else is plain geometry and unit conversion, which the calculator does with exact factors.
- How much does it cost to build a basement or foundation?, HomeGuide, no date shown on the page, read Nov 2026. Used for: the calculator’s US slab ($5.75–13.50), crawl space ($7–14) and pier and beam ($7–11) per sq ft; unfinished basement $33 per sq ft; monolithic slab $5–14; reinforced 6 in slab $6.40–10.30; stem wall $50 per linear ft; footings $6.50 per sq ft or $150 per cu yd; ready-mix $120–150 per cu yd; poured 8 in wall $12.75 and block $12–18 per sq ft; slab labor $2.60 and concrete $3.81 per sq ft and its labor/material table; contractor labor $50–150 an hour; excavation per cu yd and per sq ft; new basement dig $10–20 per sq ft; fine grading; permits $500–1,500; engineer $100–220 an hour; soil test $1,000–5,000; inspections $150–1,300; waterproofing $1,900–6,300; reinforcement $150–500 and raft rebar $1–2 per sq ft; basement cost split 45/38/17%; an 8 hour pour with 3 people; 2–4 weeks for a basement
- 2024 Foundation Cost: Slab, Crawl Space, Basement and More, Angi, updated July 12, 2024. Used for: the calculator’s US basement price ($20–37 per sq ft); monolithic slab $5–16, crawl space $6–18 and pier and beam $6–12 per sq ft; footings about $6.50 per sq ft
- How Much Does It Cost to Build a Foundation?, Fixr, updated February 13, 2026. Used for: slab $4–14, slab-on-grade $4–12, monolithic $4–16, stem wall slab $6–18, crawl space $10–18, basement $20–50 and pier and beam $6–15 per sq ft; cost by house size; labor 40–60% of the total; block walls cheaper than poured; permits up to $2,300; waterproofing about $5,000; 40 × 60 slab about $24,000; framing after about a week and a 28 day cure
- How Much Does a Foundation Cost in 2025?, HomeAdvisor (Angi Inc.), no date shown (title says 2025), read Nov 2026. Used for: basement $20–37 and pier and beam $6–12 per sq ft, the same figures as Angi
- New home foundation cost guide, Checkatrade, article 4 April 2023, cost table May 2024. Used for: the calculator’s UK prices: strip foundation £95–115 per metre with an excavator (£170–220 hand dug), trench fill £130–160 per metre (£145 typical), raft £200–260 per m² (£230 typical)
- Concrete Foundation Cost, MyJobQuote, last updated 18/09/26. Used for: raft £150–300 per m²; strip £70–78 and trench fill £84–87 per m² of footprint for a 15 × 9 m building
- Concrete Contractor Costs in Toronto, HomeStars, updated 21/08/2026. Used for: the calculator’s Canadian prices: slab $8, crawlspace $15 and basement $35 per sq ft
- Concrete Contractor Costs in Calgary, HomeStars, no date shown, read Nov 2026. Used for: foundation construction $6–15 per sq ft and foundation slab pouring $5.50–9 per sq ft
- Concrete Slab Cost: Key Insights, HomeStars, no date shown, read Nov 2026. Used for: basement floor slab $4–8 per sq ft ($2,400–4,800 for 600 sq ft)
- How much does a concrete slab cost per square metre?, Yellow Pages Australia, published 22 February 2025, last updated May 2026. Used for: the calculator’s Australian price: house foundation slab $75–110 per m²
- How much does concreting cost?, Yellow Pages Australia, published 12 February 2025, last updated May 2026. Used for: standard residential slabs $70–100 per m²
- Concreting services and costs, Airtasker (Australia), last updated 7 November 2026. Used for: plain slab $65–85 per m²
- Concreting services, Airtasker (New Zealand), last updated 31 October 2026. Used for: the only New Zealand figure found: a generic concrete slab at $50–70 per m², not a house foundation
- Kosten einer Bodenplatte: mit diesen Preisen müssen Sie rechnen, sanier.de, 27 July 2026. Used for: the calculator’s German slab prices: simple Bodenplatte €120–160 per m², insulated to the current energy standard €160–220 per m²
- Was kosten Fundamente?, sanier.de, updated 17 December 2025. Used for: the calculator’s German strip footing price (Streifenfundament €150–250 per running metre); large house Plattenfundament €70–100 per m²
- Kostenbeispiel: Bodenplatte pro Quadratmeter, Hausjournal, published 02.09.2013, updated 23.06.2022. Used for: Bodenplatte €130–250 per m² all in, including earthworks
- Kostenbeispiel: Keller, Hausjournal, published 10.04.2014, updated 31.10.2024. Used for: the calculator’s German basement price (cast-in-place Ortbeton-Keller €250–400 per m²); basement shell €200–400; precast Fertigkeller €150–200 per m²
- Kostenbeispiel: Streifenfundament, Hausjournal, 12 December 2024 (first published 30.08.2013). Used for: strip footing €200–350 per m² of strip area
- WAC 51-51-0403, Section R403 Footings, Washington State Legislature (State Building Code Council), certified 3/27/2024, adopts the 2021 IRC with state amendments. Used for: minimum concrete footing of 12 in wide and 6 in deep (a guide; your local code decides)
- Footings, Foundations and Slabs, City of Grand Rapids, Minnesota, undated, 2015 Minnesota State Building Code. Used for: exterior footings 12 in below undisturbed ground, a local frost depth of 60 in as an example, and two #4 bars 3 in above the bottom of the footing as a recommendation
- Nominal is a four-letter word, For Construction Pros (Concrete Foundations Association), December 7, 2017, quoting ACI 332-16. Used for: ACI 332 minimum foundation wall thickness of 7.5 in actual
- 4.3.7 Safe transmission of loads (strip and trench fill foundations), NHBC Standards, page last updated 2 January 2024. Used for: strip foundations 150–500 mm thick, trench fill at least 500 mm, width at least the wall plus 50 mm each side
- NIST Handbook 44, Appendix C: General Tables of Units of Measurement, National Institute of Standards and Technology, 2026 edition. Used for: 1 cu yd = 27 cu ft and the exact factors 1 ft = 0.3048 m and 1 sq ft = 0.09290304 m² that the calculator uses
Frequently asked questions
How much does a concrete foundation cost per square foot?
In the US, a slab runs $5.75–13.50 per sq ft (HomeGuide, undated) or $4–14 (Fixr, Feb 2026). A crawl space is $7–14 (HomeGuide) and a basement $20–37 (Angi, Jul 2024) or $20–50 (Fixr). The calculator uses HomeGuide for slab, crawl space and pier and beam, and Angi for basements.
How much does a slab foundation cost for a 2,000 sq ft house?
At HomeGuide’s $5.75–13.50 per sq ft, a 2,000 sq ft slab is 2,000 × 5.75 = $11,500 up to 2,000 × 13.50 = $27,000. The calculator shows the middle, $19,250. Fixr gives $10,000–70,000 for 2,000 sq ft across all foundation types, so check which type a quote is for.
Is a slab cheaper than a crawl space or basement?
Usually, yes. For a 1,200 sq ft house the calculator shows $11,550 for a slab, $12,600 for a crawl space and $34,200 for a full basement, all at the middle of the published US ranges. The low ends overlap: a cheap crawl space ($8,400) can come in under an expensive slab ($16,200).
How much does a basement foundation cost?
Angi and HomeAdvisor give $20–37 per sq ft, HomeGuide an average of $33 for an unfinished basement, and Fixr $20–50. A 1,200 sq ft basement is $24,000–44,400 at the Angi range the calculator uses. HomeGuide says excavation takes about 45% of a basement budget, so soil and depth move the price most.
How much does a monolithic slab cost compared with a stem wall?
Fixr (Feb 2026) gives $4–16 per sq ft for a monolithic slab and $6–18 for a stem wall slab. Angi gives $5–16 for a monolithic slab. HomeGuide lists a stem wall foundation at $50 per linear foot. A stem wall adds a short wall between footing and slab, so it takes more concrete and more forming.
How many yards of concrete for a 30x40 slab foundation?
A 30 × 40 ft slab 4 in thick is 1,200 × 4 ÷ 12 = 400 cu ft, which is 14.81 cu yd. A 12 in wide edge thickened to 12 in adds 136 ft × 1 × 0.667 = 3.36 cu yd, for 18.17 cu yd. With 10% extra, order about 20 cu yd. These are example sizes, not a design.
How much concrete is in a house foundation?
It depends on the type. In this page’s 30 × 40 ft example, a monolithic slab takes 18.17 cu yd, a crawl space with 4 ft walls 18.09 cu yd and a full basement with 8 ft walls 45.33 cu yd. At HomeGuide’s $120–150 per cu yd, the basement concrete alone is $5,440–6,800.
What share of foundation cost is labor?
Fixr says labor is 40–60% of the total. HomeGuide’s slab breakdown gives $2.60 labor and $3.81 concrete per sq ft, so labor is 2.60 ÷ 6.41 = 41%. HomeGuide puts contractor labor at $50–150 an hour. The calculator gives an installed total, so labor is already inside it.
How much does excavation for a foundation cost?
HomeGuide gives $6–10 per cu yd in average soil, $10–15 in heavy or wet soil and $50–200 where rock must be broken. For a new basement it gives $10–20 per sq ft. The per-yard rate looks like digging only, so for a basement budget the per-sq-ft figure is the safer one.
Do I need rebar in a slab foundation, and what does it add?
Most house slabs and footings carry some steel, and local code or the engineer decides how much. HomeGuide lists reinforcement at $150–500 as a line item and rebar for a raft at $1–2 per sq ft. A Minnesota building department recommends two #4 bars in footings, 3 in above the bottom.
How much does a 40x60 slab foundation cost?
A 40 × 60 ft slab is 2,400 sq ft. At HomeGuide’s $5.75–13.50 that is $13,800–32,400, and the calculator shows the middle, $23,100. Fixr says a simple 40 × 60 slab averages about $24,000. A full basement on the same footprint would be $48,000–88,800 at Angi’s $20–37 per sq ft.
How much does a foundation cost in Canada or the UK?
Canada: HomeStars Toronto (Aug 2026) lists slab $8, crawlspace $15 and basement $35 per sq ft. UK: Checkatrade gives strip footings at £95–115 per metre, trench fill £130–160 per metre and a raft at £200–260 per m² (cost table May 2024). Each price is in its own currency; nothing here is converted.
Is a block foundation cheaper than poured concrete?
The guides don’t agree. Fixr says block walls cost less. HomeGuide gives block foundations at $12–18 per sq ft and a poured 8 in wall at $12.75 per sq ft of wall, which overlaps. Get both prices from local crews. Our block calculator counts blocks, mortar and core fill if you want to price the materials.
Does a foundation need a permit and engineer?
In most places a new house foundation needs a building permit and inspections. HomeGuide gives permits at $500–1,500, Fixr up to $2,300. A structural engineer runs $100–220 an hour and a geotechnical soil test $1,000–5,000 (HomeGuide). Your building department tells you what it needs before you dig.
How long does it take to pour a foundation?
HomeGuide says a pour takes about 8 hours with a 3-person crew, and a basement dig and build takes 2–4 weeks. Fixr says many contractors start framing after about a week, with full cure at about 28 days. Inspections of the footing and steel before the pour add days to the schedule.
Why do foundation quotes vary so much?
Soil, depth, access and what the quote includes. HomeGuide puts excavation at 45% of a basement budget and rock at $50–200 per cu yd. Some quotes include permits, steel, waterproofing and backfill; others don’t. Even the guides disagree: US basement prices run from $20 to $50 per sq ft depending on the publisher.
Is this concrete foundation cost calculator free to use online?
Yes. The CalcWall Concrete Foundation Cost Calculator is completely free and works online in any browser, on a phone, tablet or computer. There is nothing to download and no account to create, and the math runs right in your browser, so results appear as you type.